Firmware update

[中文]

How does the host MCU flash ESP32 via serial interfaces?

How to download firmware for ESP32 series modules using the USB-Serial tool?

The methods are as follows:

Modules

3V3

GND

TXD

RXD

IO0

EN

Serial tool

3V3

GND

RXD

TXD

DTR

RTS

Note

For ESP8266 modules, IO15 should be specially connected to ground.

How to flash firmware in macOS and Linux systems?

  • For Apple system (macOS), you can use esptool downloaded via brew or git to flash firmware.

  • For Linux system (e.g., ubuntu), you can use esptool downloaded via apt-get or git to flash firmware.

Does ESP32 support programming using JTAG pins directly?

Yes, ESP32 supports using JTAG Pins to flash directly. Please refer to Upload application for debugging.

Does ESP_Flash_Downloader_Tool support customized programming control？

  • The GUI tool is not open-sourced and does not support embedded executive script.

  • The low-level component esptool is open-sourced and can be used to perform all functions such as flashing and encryption. It is recommended to conduct secondary development based on this component.

Can I enable the Security Boot function for ESP32 via OTA?

  • It is not recommended to enable Security Boot function through OTA, as it poses operational risks and requires multiple OTA firmware updates.

  • Since the Security Boot function is in Bootloader, please update Bootloader first to enable this function.

    1. First, check the partition table of your current device to see if it can store the Bootloader with Security Boot enabled.

    2. Then, update an intermediate firmware which can be written in Bootloader partition. By default, the Bootloader partition cannot be erased or written, you need to enable them via make menuconfig.

    3. Sign the intermediate firmware and upgrade it to the target device through OTA. Then upgrade the Bootloader of this firmware and the signed new firmware through OTA.

    4. If there are situations as powered-down or network break-down and restart during the Bootloader OTA process, the device would not be started and needs to be re-flashed.

How to resolve the following error occured when flashing firmware to ESP32-S2 based on ESP-IDF v4.1?

esptool.py v2.9-dev
Serial port /dev/ttyUSB0
Connecting....
Chip is ESP32S2 Beta
Features: Engineering Sample
Crystal is 40MHz
MAC: 7c:df:a1:01:b7:64
Uploading stub...
Running stub...

A fatal error occurred: Invalid head of packet (0x50)
esptool.py failed with exit code 2

Solution

If you are using ESP32-S2 instead of ESP32-S2 Beta, please update ESP-IDF to v4.2 or later versions.

Notes:

  • ESP-IDF v4.1 only supports ESP32-S2 Beta, which is not compatible with ESP32-S2.

  • The version of esptool came with ESP-IDF v4.1 is v2.9-dev, which only supports ESP32-S2 Beta as well.

  • Both ESP-IDF v4.2 and its esptool v3.0-dev support ESP32-S2 series chips.

How to download firmware based on ESP-IDF using flash_download_tool?

  • Please refer to get-started-guide when building an ESP-IDF project for the first time.

  • Taken hello-world example for instance, run idf.py build (Only for ESP-IDF v4.0 or later versions. Please use make for previous versions). After building, the following flash command for the bin file will be generated:

#Project build complete. To flash, run this command:
../../../components/esptool_py/esptool/esptool.py -p (PORT) -b 921600 write_flash --flash_mode dio --flash_size detect --flash_freq 40m 0x10000 build/hello-world.bin  build 0x1000 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin
or run 'idf.py -p PORT flash'

You can use flash_download_tool to flash according to the bin file and flash address prompted by this command.

What is the communication protocol for flashing ESP chips?

How to program ESP32-C3’s firmware offline?

  • Currently, there is no tool that supports the offline programming of ESP32-C3’s firmware. However, the Flash Download Tools we released can directly download binary firmware and support mass production download mode for up to eight ESP32-C3 devices at the same time.

  • In addition, we also offer the Test Fixture for mass production, which supports up to four ESP32-C3 modules to download firmware simultaneously.

How does ESP32 set Flash SPI to QIO mode?

  • It can be set in menuconfig through Serial flasher config -> Flash SPI mode, the corresponding API is esp_image_spi_mode_t().

After downloading program and powering on EPS8266, the serial port printed the following log. What is the reason?

ets Jan  8 2013,rst cause:1, boot mode:(7,7)
waiting for host

  • waiting for host means the Boot is in SDIO mode, indicating that GPIO15 (MTDO) is pulled up (HIGH). Please refer to ESP8266 Boot Mode Description.

What are the Espressif module programming tools?

  • For Espressif programming software, please go to Flash Download Tools. Installation-free GUI tools for Windows environment only.

  • Espressif programming tool esptool is written based on Python with open-source code, supporting secondary development.

What is the difference between the Factory mode and Developer mode of the flash download tool?

  • Factory mode supports multi-channel downloads, while Developer mode only supports single channel.

  • The path of bin files under the Factory mode is relative, while under Developer is absolute.

Why does the programming failed for the jig with a 4-port hub in factory mode ?

:CHIP: ESP32 | ESP8266 :

  • It is because Espressif products complete the calibration operation through transmitting some packets when starting up. This operation requires 3.3 V voltage and a guaranteed peak current of 500 mA. Therefore, when it comes to more than one ports, there will be situations where the computer cannot program or the programming is interrupted due to the insufficient power supply of the computer’s USB when programming via connecting to a computer’s USB. It is recommended to use the hub for programming and supply power to the hub in the meantime.

I’m using an ESP32-WROVER-B module to download the AT firmware via the flash download tool. However, an error occurred after writing to flash. But the same operation succeeded when replacing the module with ESP32-WEOVER-E, what is the reason?

  • The ESP32-WROVER-B module leads out the SPI Flash pin, but the ESP32-WROVER-E module does not. Please check whether the SPI Flash pin of the ESP32-WROVER-B module is re-used by other external application circuits.

  • Connecting the CMD pin of the SPI Flash in ESP32-WROVER-B to GND will cause the flash failing to start. And the following error log will be printed:

rst:0x10 (RTCWDT_RTC_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT)
flash read err, 1000
ets_main.c 371
ets Jun 8 2016 00:22:57

The encrypted device cannot be re-flashed via the flash download tool. What could be the reason?

CHIP: ESP32 | ESP32-S2

  • Currently, an encrypted device cannot be flashed again using the flash download tool. It only supports one-time encryption of plaintext.

When updating ESP32 firmware through UART interface based on esptool serial port protocol, can I add a new app partation?

  • The partitions in flash depend on the data in partition_table.bin. If partition_table.bin can be updated, the storage space of other data, such as bootloader.bin and app.bin, can be redivided to create an app partition.

I am using ESP8266 to download the firmware via flash download tool. After downloading the firmware, there is no programming output log, and the serial port printed the following messages. What could be the reason?

ets Jan  8
2013,rst cause:1, boot mode:(3,7)
ets_main.c

  • Please check whether the hardware wiring is correct. See Boot mode wiring instructions.

  • Please check whether the download offset address of bootloader.bin is correct. The offset address downloaded from bootloader.bin of ESP8266 is “0x0”. If the offset address is wrong, the flash cannot be started.

Why does my USB driver failed to be recognized by the Windows7 system?

  • Please download and install the USB Serial JTAG driver <https://dl.espressif.com/dl/idf-driver/idf-driver-esp32-usb-jtag-2021-07-15.zip> manually for the Windows7 system.

After using the ESP32-WROVER-E module to download the program, the following log is printed after powered on. What could be the reason?

  rst：0x10 （RTCWDT_RTC_RESET），boot:0x37（SPI_FLASH_BOOT）
【2020-12-11 15:51:42 049】invalrd header：0xffffffff
  invalrd header：0xffffffff
  invalrd header：0xffffffff

  • Generally, it is because the GPIO12 was pulled high. It is recommended to pull it low and see the results. Please see ESP32 Boot Log Guide.

When using the Flash Download Tools to flash ESP32-C3 via USB, 8-download data fail occurs repeatedly. How can I solve it?

  • Please erase the chip completely first before flashing

  • This problem has been solved in V3.9.4 and above versions


Suggestion on this document?

 Provide feedback